Lynex TX2500

Lynex TX 2500 is a 250 hp tool carrier on tracks.

TX 2500 has the markets lowest center of gravity and maximum ground clearance in the same time. The cab is placed in rear linkage and can be removed without tools.

The machine is remote controlled as the LX 1000 the new machine has linkage at both ends and can run with all tools for. example a mulcher.

Power loss on transmission are among the lowest,  245 hp at the Front-PTO. The machine is also equipped with a turbine clutch to take the shock  of the transmission line.

Engine-transmission

The 250 hp Perkins engine provides plenty of power to even the most difficult challenges. The small weight of 5 tons only need a minumum of power to move forward. The hydrostatic piston pumps has the best efficiency, and saves fuel. The transmission consists of a Zuiderberg gearbox and turbine clutch, which takes all the shocks loads off the machine.

Suspension undercarrier/ Chassis.

Tx 2500 has been newly designed Patent Pending undercarriage. This chassis is hydraulically suspendet  in all 4 corners. This means that the strong chassis always follow a straight line above the earth's surface and the shock is absorbed in the suspension and the tool  is moving quietly in a straight line from the ground. The rubbertracks can be adjusted hydraulically between 2.1 m and 3 m total wide (depending on equipment), ground clearance is also adjustable between 10 and 55 cm, and can in that way get gravity of only 50 cm on slopes. On wetlands the clear height can be increased so underbody machine is not hanging on the chassis.

Rubber tracks

Tracks are hydraulically suspended. This means, if there will be a rock or stone into the belts, the hydraulic suspension will just  forsh back until the stone is dispersed. Belts are always drawn by the same pressure and are self tightened. Another big advantage of this system is that the entire belt can be switched to a wider belt on the same chassis, and this can be done during a 30 min completely without tools.

Radiator

Radiator blades can reverse the air flow at full load, the radiator is always clean and efficient. Cleaning with compressed air is not necessary any more.

Application

  • walls / cliffs -Wetlands
  • Water Pools-Road construction
  • Antiquities-Natural areas

 

Specifications

Type TX 2500
Motor Perkins 250 HK
Slopes up to 45 degress in all directions
Weight 4985 kg
Speed forward/reverse (0-5) (0-10) (0-15) (0-20) 4gier
Turning radius 0 degrees
Transport Width 2200 cm
Height 165 cm
Length 148 cm
Center of gravity 56 cm above the ground

 

ISS

Under the work for the railway network, we have focusing on work environment.
ISS have some difficult spaces on the track area with slopes of up to 60 degrees.
We were very skeptical when Lynex machine showed up because we had already tested some others types of slope mowers  with disappointing results. It turned out soon that the machine could run on our slopes with no problems.
We place great emphasis on safety and working environment. In 2008 we purchased  two Lynex LX 1000 in order to get even better safety and security for staff on the slopes. The secondary gain was a saving of number of man hours.
The machine can work on the slopes in any weather, which was an impossibility in the old days when we went on the steep slopes, which was very slippery in the rain due to the high clay content in soil.
Machine "crush" the grass, wich make a quick decomposering even after cutting the high grass.
Today we have much less challenges with security for the people who no longer need to move on the slopes. They do not get as tired as they do not have to go with a machine on the slopes, but is at a safe distance, without body vibration, ankle injuries or other hazardslet .
Lynex gives security for the working peopel, because the machine is in a safe distance. and it is very confortabel,

Vejle County

Vejle county has 295 rainwater pools.

When they need a new slopemower, the choice was no coincidence. They tried several different machines, and Tommy Rasmussen tells, he was not in doubt in Lynex, when he had to take the choice for a new efficient machine.

The choice was no coincidence when we should have a new machine to mow our rainwater pools. We tried several different slope mowers tells Tommy Rasmussn. When he had to take the choice for a new, efficient machine.

Lynex has a much higher capacity and it is significantly better centre of gravity, compared to the other alternative. The reason is that a Lynex uses the strength to mow the grass and not to come forward.

The remote is extremely easy and joystick is very soft, so even if you must run the machine 8 hours each day, you will not hurt either thumb your  back.
Tommy Rasmussen tells also. The fact that the entire machine can be controlled with one hand, is a big advantage,  when I  talk on the phone while I drive.
There are few moving parts in the machine and it is incredibly easy to maintain.
In the beginning I was a little skeptical about the chassis frame is able to keep, but now  after we have been running for over 2000 hours there is nothing to look at the chassis frame.
We've run in rain water tanks, which have not been mowed in 30 years. In the beginning I was very nervous, when the machine drive into an old bike or a large stone, but now I just reverse with the machine, when I hear noises,  removes the obstacle and continue. Tommy adds that often you drive blindly into the meter-high grass, not knowing what lies ahead.

Lynex LX1000

The Lynex LX1000 is a radio controlled flail slope mower designed for mowing slopes of up to 75 degrees

With very low ground pressure the machine is particularly useful in ecologically sensitive areas and over soft ground.

The machine cuts long grass and light scrub but also provides a very good finish on short mown areas.

The reliable transmission, combined with powerful cutting high performance even under difficult conditions, and the machine is ideal for mowing on steep slopes at water reservoirs and nature reserves.

The unique engine mounts ensures that the engine always in vertical position during operation.
The deck has great absorbency and also provides great cutting capacity.

The Fail Safety system monitor the machine under all conditions. We have developed our own remote which only weighs half the weights of others remotes which raises considerable discomfort.

 Safety features include an emergency single action cut out switch on the hand control, and another located on the machine itself

Application Areas:

  • walls / cliffs-Wetlands
  • Water Pools-Road construction
  • Antiquities-Natural areas

Specifications

Type LX1000
Motor Perkins 22 hp
Slopes up to 75 degrees
Weight 295 kg
Speed forward/reverse 7,5 km/h
Turning radius 0 degrees
Working Width 100 cm
Height 67 cm
Length 153 cm
Center of gravity 26 cm above the ground

 

Lynex GX1500

GX 1500 makes the impossible possible. Never before has a tool carrier been able to adapt to the situation with perfection.
Gravity and ground clearance

The center of gravity on the GX1500 can be moved to the extreme. The hydraulically adjusted between 10 and 55 cm, which provides optimal opportunities to drive on slopes up to 45 degrees, and on marsh land or water. This happens with a small touch on the remote control.

The machine has hydraulic suspension in all four corners for smooth running without vibration.

Transmission / engine

The engine is the Caterpillar brand with 100 HP that provides great power to the tools one may want to put on the machine. There isn’t any V-belt on the machine, this reduces the maintenance on this model Gx 1500

The powerful transmission sits in closed well tested gearboxes. We've only used the best components to ensure the highest possible efficiency. If the machine must be running with crushes and not desired PTO operation, it also comes with a piston pump of 95 hp to the crusher. Remote Control We have developed the remote from scratch, and it is the only one on the market, that has two way communication, making it possible to get valuable information on how steep the slopes are, or how high the engine oil pressure and temperature is at all times. The electronics are in fact so robust that the remote also is sold to industrial machinery. It uses 2.4 Ghertz, which means that it has approved almost anywhere even at oil refineries. The remote has a guaranteed range exceeding 800 meters.

Coolers

The machine has a cooling capacity designed for operation in Australia. The radiator is fitted with a dust and pollen filter that effectively removes all foreign matter. As an option, GX1500 comes with reversible fan blades which are controlled from the remote.

3 point hitch, PTO.

The machine is fitted as standard with 3 point hitch on the rear end and front.
This allows the GX1500 to run all tools that a tractor can run. Our PTO is mechanically which means that 98% of the effect is on the PTO and therefore no transmission loss here.

Application

  • Walls / cliffs -Wetlands
  • Water Pools-Road construction
  • Antiquities-Natural areas

Specifications

Type GX1500
Motor Perkins 100 hp 4.4 L Turbo
Slopes up to 45 degress in all directions
Weight 2200 kg
Speed forward/reverse (0-2) (0-5) (0-7,5) (0-10)
Turning radius 4gier 0 degrees
Width 1.6 to 2.3 meters
Height 1.1 to 1.7 meters
Length 3.1 meters
Center of gravity between 0.3 and 1 m